KODE HURUF PADA SKEMA MOTHERBORD LAKTOP

MENGENAL KODE HURUF DALAM SKEMA MOTHERBOARD

KODE HURUP KOMPONEN 

C                                   :CAPASITOR
D                                   :DIODA
F                                   :FUSE
L                                    :INDUKTOR
PC                                :POWER CAPASITOR
PD                                :POWER DIODES/DIODA
PL                                 :POWER INDUCTOR
PQ                                :POWER TRANSISTOR
PR                                :POWER RESISTOR
PU                                :POWER INTEGRATED CIRCUIT
Q                                  :TRANSISTOR
R                                   :RESISTOR
T                                   : Transformers
U                                  :INTEGRATED CIRCUIT/BGA CHIP/EMBEDDED CONTROLER/BIOS IC,ETC
X                                   : Terminal strips, terminations, joins .oscilator
Y                                   : Crystal

ISTILAH DALAM LAPTOP MOTHERBOARD DAN SCHEMATIC

AC                                : Alternating current
ACDRV                       : AC adapter to system-switch driver output
ACEDET                      : Adaptor Current Detector
ACGOOD                   : Valid adapter active-low detect logic open-drain output
ACIN                           : Adaptor Current sensor Input
ACN                             : Adapter current sense resistor
ACOP                          : Input Over-Power Protection
ACOV                          : Input Overvoltage Protection
ACP                             : Adapter current sense resistor, positive input.
ADP+                          : Adapter Positif Suplay
ADP_ID                      : Adapter Identity
AGND                         : Analog Ground
ALWP                          : ALWAYS ON POWER
 B+                               :AC OR BAT POWER RAIL FOR POWER CIRCUIT
BATT                           : Battery

BAT+                           :BAT POWER RAIL FOR POWER CIRCUIT
BAT_DRV                  :Bat Fet Gate Driver
BAT_V                        : Battery Voltage
BOM                           :BILL OF MATERIAL MANAGEMENT
BT                                 : BUTTON
BT_EN                        :Bloototh Enable
BUZER                        :Connected
BYP                              :Baypass
CHGEN                       : Charge enable active-low logic input
CIN                              : Input Capacitor
CLK_EN                      : CLKOCK ENABLE
CN                                :CONECTOR
CRT                              :Cathode ray tube
CSIN                            :Current Sensor input Negatif
CSIP                             :Current Sensor input Positif
DC                                :Direct current
DM                              :DIM/DIM SOCKET/SOKET MEMORY/SOKET DDR
DKHAZ                        :Dhea-Kautsar-Hafidz-Ali-Zahra
DOCK                          :DOCKING SOCKET
EC                                 :Embedded Controler
EC_ON                       :Embeded Controler Enable
EMI                              :Elektromagnetik Interference(GANGGUAN ELEKTROMAGNETIK)
EN                                :ENABLE
ENTRIP                       :Enable Terminal
F                                   :FUSE
FSEL                             : Frequency Select Input.
GATE                           : Trigger gate
GND                            :Ground
GP                                :GROUND PIN
GPI                              :General Power Input
GPIO                           :General Power Input Output
HDMI                          :High-Definition Multimedia Interface
ID                                 :Continuous Drain Current
IDM                             :Pulsed Drain Current
IIN                                : Operating Supply Current
IIN(SHDN)                 : Shutdown Supply Current
IIN(STBY)                   : Standby Supply Current
IS                                  :Continuous Source Current (Diode Conduction)
IVIN                             :Battery Supply Current at VIN pin
JP                                 :JUMPER POINT
KBC                              :Keyboard Controler
LCDV                           :LCD POWER
LDO                             :Linear Driver Output
LGATE                         : Lower-side MOSFET gate signal
LPC                              :Low Pin Count
LVDS                           :Low-voltage differential signaling(SYSTEM PENSIGNALAN)
MBAT                         :MAIN BATTERY
NB                                :North Bridge
ODD                            :OUTPUT DISC DRIVE
PCI                               :Peripheral Component Interconnect
PGOOD                      : Power good open-drain output
PIR                               :PRODUCT IMPROVED RECORD
PSI#                             :Current indicator input
PVCC                           : IC power positive supply
RSMRST                     : Resume Reset
RTC                              :REAL TIME CLOCK
SB                                 : South bridge
SHDN                          :Shutdown
SYS_SDN                   :System Shutdown
SPI                               :Serial Peripheral Interface
TD                                :Death Time
THRM                         :THERMAL SENSOR
TMDS                          :Transition Minimized Differential Signaling(TRANSMISI DATA TEKNOLOGY)
TP                                 :TES POINT
TPAD                           :THERMAL PAD
UVLO                          : Input Undervoltage Lock Out
V                                   :RAIL(POWER)
V+                                :Positive Voltage
VADJ                           : Output regulation voltage
VALW                         :ALWAYS ON POWER
VALWP                       :VALW PAD
VBAT                           :BATTERY POWER
VCCP                           :power chip(ich,graphic chips)
VCORE                        :POWER PROCESOR
VDD                             : Control power supply
VDDR                          :POWER DDR (VDRAM/VRAM/VMEM)
VDS                             :VOLTAGE DRAIN SOURCE
VFB                              : feedback inputs Power
VGS                             :VOLTAGE GATE SOURCES
VIN                              : Input Voltage Range
VIN                              :ADAPTER POWER SUPLAY(vol_in)
VL                                 :Power Lock
VL                                 :voltage across the load/Tegangan beban resistor
VL                                 :Voltage Linear
VLDOIN                      :Power supply of the VTT and VTTREF output stage (to powerMOS).
VOT                             :Volt_out
VRAM                         :Power Memori
VREF                           :POWER REFERENCES/SCHEMA REFERENCE/PERMINTAAN SKEMA
VS                                :SUITCH POWER
VS+                              :SUPPORT VOLTAGE POSITIF
VSB                              :POWER SWITCH BUTTON
VSS                              : Signal ground.
VSW                            :POWER SWICT
VTT                              : Memory Termination Voltage
VTERM                       :Memory Termination Voltage
VUSB                          :POWER USB
VGA                            :POWER VGA (VGPX/VGPU/VCVOD)
VGFX                          :POWER GRAPHIC CHIP  
VREF                           :VOLTAGE REFERENCES

Posted in: